●AWD-coverパネルは下記の5種類の中から選べます。


typeH2:\5800(in tax)

●SUS-304,t=1.5mm
●ヘアライン仕上げ



typeA:\9800(in tax)

●終了しました。




typeB:\12800(in tax)

●SUS-304,t=1.5mm
●ヘアライン仕上げ
●黒文字+ツートン印刷
●パイロットランプ仕様

typeW:\12800(in tax)

●SUS-304,t=1.5mm
●ヘアライン仕上げ
●白文字印刷+ウッド調
●パイロットランプ仕様

typeBLK:\15800(in tax)

●SUS-304,t=1.5mm
●黒塗装仕上げ
●白文字印刷
●パイロットランプ仕様

�@メーターCOVER パネル...typeH1,typeH2 ●装着方法はこちら
画像typeH:厚さ1.5mm

●メーターCOVERパネルNA:ヘアライン仕上げ

●typeH1(純正リング流用サイズ)終了しました。
●typeH2(AWDリング装着用サイズ)\5800


● 画像にはAWDリング等の、別売オプション製品が装着されています。


純正のプラ素材の質感を隠し、AWDメーターをより一層際立たせグレードアップさせるアイテム。 ボリュームを感じさせる厚さは異例の1.5mm。
素材はステンレスヘアライン仕様。超耐久性マフラーなどへの使用で知られている"SUS304"鋼材をチョイス。


★注意:typeH1とtypeH2,の2種類のサイズがあります。(H1type:は終了しました)

●type-H1

●純正のメッキリングをそのまま使用する場合は
メインメータ外側が0.3ミリ大きくなりますのでそのサイズに合わせたtype-H1,になります。

●(H1サイズは終了しました)

●type-H2

●1800sr2の様に純正メッキリングの設定がないタイプは0.3mmほどスキマがあくので
それを修正したサイズのtypeH2となります。

AWDリング装着の場合は純正メッキリングを外すのでNA6Cでもtype-H2,になります。


Installation guide : M1 gauge cover panel & Ring
To separate the gauge cover panel from the assembly, push in the black plastic tabs on top and the bottom of the housing using a flat blade screw driver.


Next step is to separate the clear acrylic cover from the base. The clear cover is glued to the base and must be cut away using an inexpensive acrylic cutter (available at home improvement centers). Using gentle pressure, score the acrylic cover several times until the scoring line is quite deep. Gently twist the cover from the base to separate. The resulting cut should be smooth and clean. If there are minor cracks or irregularities, do not worry since the dash pod will hide them once reinstalled.

Although the double sided tape should be strong enough to hold the AWD panel cover, the use of additional screws (included in the package) is recommended. First drill pilot holes before attaching the screws. Once the panel cover is installed, remove any OEM rings before installing AWD rings.
Once the installation of AWD panel cover and the AWD rings are complete, reverse the disassembly process. The clear Acrylic cover does not have to be glued back since the pressure from the dash pod cover will hold it in place once reassembled.

Gauge face/ Version MC(NA)
cover panel/ typeH
AWD ring/ type Vintage(new!)